Thermaroof TR26 is designed for flat roof insulation with mechanically fixed single-ply waterproofing. Download the specification here. INSULATION FOR FLAT ROOFS WATERPROOFED WITH. MECHANICALLY FIXED SINGLE-PLY WATERPROOFING. Seventh Issue. October TR26 LPC/. These examples are based on Kingspan Thermaroof® TR LPC/FM, waterproofed using a mechanically fixed single–ply membrane. The insulation board is.
|Published (Last):||19 January 2018|
|PDF File Size:||16.45 Mb|
|ePub File Size:||8.33 Mb|
|Price:||Free* [*Free Regsitration Required]|
This Thermaroof Range includes the following readily available product thicknesses 25mm, 40mm, 50mm, 60mm, 70mm, 80mm, 90mm, mm, mm, mm, mm and mm. Unfortunately, further to the recent supply challenges with PIR and Phenolic insulation boards from Celotex, Kingspan, Ecotherm and Recticel, available stock of these product will vary throughout the country.
Thermaroof TR26 LPC/FM
However, the total required dry weight will depend upon wind uplift, which in turn will vary with the geographical location of the building, local topography, and the height and width of the roof concerned. Insulation for flat roofs waterproofed with partially bonded torch applied multi—layer bituminous waterproofing.
Installing over Concrete Decks Concrete decks should be clean, dry, without large projections, steps or gaps, and should be graded to allow correct falls to all rainwater outlets. Where one run of the specified vapour control layer laps another, there should be minimum mm side and end overlaps, which should be adequately sealed.
Help or advice needed for your project?
Therma TR26 | Insulation for Waterproofed Flat Roofs | Kingspan | New Zealand
Subject to product availability locally, and vehicle delivery slots. ThermaRoof TR26 is a foil faced insulation for flat roofs with mechanically fixed single-ply waterproofing. There should be no gaps at abutments.
Learn kingsppan acoustics in buildings. If correctly applied, the TR26 Boards have an indefinite life. Result Dependent on single-ply membrane adopted Further details on the fire performance of Kingspan Insulation products may be obtained from the Kingspan Insulation Technical Service Department see below. Insulation boards should always be laid break-bonded, either with their long edges at right angles to the edge of, or diagonally across the roof, and with joints lightly butted.
A minimum separate vapour control layer should consist of a gauge micron polythene sheet, with all joints lapped and then sealed with double sided self adhesive tape. Kingspan TR26 40mm, 8 x 1. Boards of TR26 should be secured to the deck using mechanical fixings e. Where these requirements cannot be ensured, the insulation must be mechanically fixed.
Therma TR26 FM Roof Board
Where this is not the case, a separate vapour control layer should be installed. Roof Waterproofing TR26 is suitable for use with most mechanically fixed single-ply waterproofing membranes. When installing a loose-laid insulated green roof assembly, any insulation must be immediately over-laid with the green roof system, which must meet all of the requirements outlined above. Further details of Kingspan Thermataper TT46 are available from the Kingspan Insulation Tapered Roofing Department see rear coverwhich should be consulted as early as possible in the process of designing a roof.
Part 1 FM approved for Class 1 steel deck roof assemblies Fully compatible with most mechanically fixed single-ply waterproofing systems Compatible with most green roof systems Installation technique is ideal for fast track building programmes Resistant to the passage of water vapour Easy to handle and install Ideal for new build and refurbishment Non-deleterious material Manufactured with a blowing agent that has zero ODP and low GWP.
Kingspan TR26 mm, 2 x 1. Contact our experienced technical services department today.
Thermaroof TR26 LPC/FM | Insulation | Kingspan | MEA & India
Select products below to see pricing structure Use product tick-boxes to select required products Add to Basket Kingspan TR26 25mm, 12 x 1. TR26 is suitable for use on access roof decks subject to limited foot traffic.
A new secondary school situated right at the heart of one of the UK’s most ambitious regeneration projects. If the metal deck is not sealed the vapour control layer should be loose-laid.
Share Twitter Facebook LinkedIn. Insulation boards should always be laid break-bonded, either with their long edges at right angles to the trough openings, or diagonally across the corrugation line, and with joints lightly butted.
The insulation core is resistant to short—term contact with petrol and with most dilute acids, alkalis and mineral oils. Quick links Product information.
Regardless of the deck type it is recommended that a condensation risk analysis is carried out for every project. Turn up the vapour control layer at the edge of the roof to a height appropriate to the specified waterproofing membrane. The most rr26 board sizes may be available from stock.
If using a sealed metal deck there is no requirement for a separate vapour control layer. This may affect the rates; we will of course discuss possible solutions with you before proceeding and will do our best to keep additional costs down. Kingspan TR26 50mm, 6 x 1.
Kingspan TR26 80mm, 4 x 1. High performance insulation for flat roofs Kingspan Therma TR26 FM Roof Board is an insulation board with a rigid thermoset polyisocyanurate PIR fibre free insulation core, faced on both sides with a low emissivity composite foil.
Specifications Thermal conductivity 0.